CCIE Data Center Training Course
Prerequisite for CCIE Data Center Training:
NEW QUESTION: 1
Which two types of traffic are consolidated using Cisco unified Fabric? (Choose two)
A. video traffic
B. voice traffic
C. network traffic
D. SAN storage traffic
E. InfiniBand traffic
NEW QUESTION: 2
Which three functions are Key characteristics of the data center access layer in a three-tier
A. performs QoS marking
B. must support routing protocols such as OSPF and BGP
C. provides connectivity to network based services (load balancer and firewall)
D. provides connectivity to the servers
E. segment workgroups
F. implemented in top-of-rack or end-of row topology
NEW QUESTION: 3
Which two statements about ACI border leaf are true? (Choose 2)
A. The border leaf can also be used to connect to compute, IP storage, and service appliances.
B. The border leaves are ACI leaves that provide Layer 3 connections to outside networks.
C. The border leaves are dedicated leaf switches that support only Layer 2 and Layer 3 out in an ACI
D. Only 32 border leaves are supported in an ACI fabric
NEW QUESTION: 4
Which three port types support port security in Nexus 7000? (Choose three)
A. Layer 2 and Layer 3 ports
B. access ports
C. SPAN destination ports
D. trunk ports
E. SPAN source ports
F. vPC ports
NEW QUESTION: 5
Which two guidelines and limitations of PTP on Cisco NX-OS are true? (Choose two)
A. PTP can be enabled only on F - and M - Series module ports.
B. Only one PTP process can control all of the port clocks through the clock manager.
C. PTP supports transport over UDP. Transport over Ethernet is not supported.
D. PTP is limitless per network
E. PTP supports multicast, unicast, and anycast communication
NEW QUESTION: 6
Drag and drop the MST Spanning Tree protocol standards from left onto the correct
characteristics on the right.
NEW QUESTION: 7
How is the virtual IP for an ACI VPC domain assigned?
A. by DHCP using the default management network
B. No virtual IP is available for VPC peers on ACI
C. manually by the admin
D. by DHCP using the infrastructure VLAN
NEW QUESTION: 8
Which description of how to enable the Flex Flash Controller auto-sync function on the
B200M4 blade is true?
A. Configure a local disk policy for FlexFlash
B. Configure a storage policy for FX3S
C. Enable auto-sync in the servers > inventory > storage subtab
D. Configure a storage connection policy to use auto-sync
NEW QUESTION: 9
Refer to the exhibit.
When adding an ASAv to the APIC, the user notices a fault raised on the device. Which cause of this
fault is the most likely?
A. The incorrect username and password was used
B. The configuration did not specify "apic" as the username
C. The device package was never uploaded
D. The configuration specified HTTP and not HTTPS
NEW QUESTION: 10
Which two statements about configuring the Intermediate System-to-Intermediate System
domain policy on an ACI Fabric are true? (Choose two)
A. PIM hello messages are sent to 184.108.40.206 and the router with the lowest priority is selected as the
B. The IS-IS domain policy is configured under Fabric > Access Policies
C. PIM hello messages are sent to 220.127.116.11 and the router with the highest priority is selected as
D. The IS-IS LSP generation initial wait, maximum wait, and second wait intervals can all be configured
E. The IS-IS default MTU is set at 4352, and it cannot be changed
F. PIM exchanges unicast hello messages between all routers advertised by the anycast RP
G. The IS-IS fast-flooding of link state packets improves IS-IS convergence time
H. Cisco Nexus stitches do not have a concept of DR due to vPC
I. The IS-IS domain policy is configured under Fabric > Global Policies
NEW QUESTION: 11
Which three editing optional of Cisco UCS Director workflow are valid? (Choose three)
A. Reorder inputs
B. Change an input from mandatory to optional
C. Rename a workflow
D. Delete inputs
E. change priority of a workflow
F. Edit tasks in the workflow
NEW QUESTION: 12
Refer to the exhibit.
Which purpose of the ipospf transmit-delay command is true?
A. This variable is used by the OSPF to send hello packets periodically after the time specified in the
B. This variable sends the OSPF database to the neighbors periodically after the time specified in the
C. This variable adds a specified time to the age field of an OSPF update. This parameter has more
significance on very low-speed links.
D. This variable is used to negotiate transmit -delay with the OSPF neighbors.
More relating informaton exam 400-151: